X650B clone firmware needed
Posted: Fri Jun 12, 2020 5:58 pm
Action : Boot Info.
Selected 0-By CPU:ELBRUS
Exe version: NCKBox AndroidMTK 2.8
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM13)
Boot mode: Preloader
BBCHIP: 6580 0 ca00
Using Algo 1.
Phone detected...Please wait
Sending DA agent, please wait...
----------------------------------------------------
BaseBand CPU :MT6580
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 1 GB DRAM
----------------------------------------------------
EMMC: (29Gb+8192Mb) HYNIX 0x483447316404
EMMC FW VERSION: 05:00:00:00:00:00:00:00
EMMC CID: 90014A483447316404 : 00000000000000
EMMC UA SIZE: 0xe9000000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0xe9c00000 [3.652 GB]
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detected : MediaTek DA USB VCOM (Android) (COM15)
[system]Reading info, wait...
Build ID: LMY47I
Display ID: C529_80L_WE_3GW_B125_EMMC_DDR2_32_8_QHDP_BE_K1A1G_K17_20190925-115021
Version: 5.1
Build Date: Wed Sep 25 11:50:21 CST 2019
Model: K17
Brand: K17
Device: K17
Model: K17
Model: X650B
Manufacturer: K17
Region: US
Mediatek Version Release: ALPS.L1.MP6.V2_YUANDA6580.WE.L
FRP partition: /dev/block/platform/mtk-msdc.0/by-name/frp
This phone have FRP partition.
IMEI[1]: 355870462205011
IMEI[2]: 355870462205029
Wait untill phone will start charging.
[0]All done.
somebody help me thanks
Selected 0-By CPU:ELBRUS
Exe version: NCKBox AndroidMTK 2.8
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM13)
Boot mode: Preloader
BBCHIP: 6580 0 ca00
Using Algo 1.
Phone detected...Please wait
Sending DA agent, please wait...
----------------------------------------------------
BaseBand CPU :MT6580
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 1 GB DRAM
----------------------------------------------------
EMMC: (29Gb+8192Mb) HYNIX 0x483447316404
EMMC FW VERSION: 05:00:00:00:00:00:00:00
EMMC CID: 90014A483447316404 : 00000000000000
EMMC UA SIZE: 0xe9000000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0xe9c00000 [3.652 GB]
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detected : MediaTek DA USB VCOM (Android) (COM15)
[system]Reading info, wait...
Build ID: LMY47I
Display ID: C529_80L_WE_3GW_B125_EMMC_DDR2_32_8_QHDP_BE_K1A1G_K17_20190925-115021
Version: 5.1
Build Date: Wed Sep 25 11:50:21 CST 2019
Model: K17
Brand: K17
Device: K17
Model: K17
Model: X650B
Manufacturer: K17
Region: US
Mediatek Version Release: ALPS.L1.MP6.V2_YUANDA6580.WE.L
FRP partition: /dev/block/platform/mtk-msdc.0/by-name/frp
This phone have FRP partition.
IMEI[1]: 355870462205011
IMEI[2]: 355870462205029
Wait untill phone will start charging.
[0]All done.
somebody help me thanks