How to Change iPhone Location | Spoof GPS Location on iPhone with Tenoshare iAnyGo (iOS 16 Supported)
Xiaomi Mi A2 Lite (Redmi 6 Pro) M1805D1SG FRP Done!
Forum rules
READ: GSM-Tutors Forum-Wide Rules and Regulations
READ: GSM-Tutors Forum-Wide Rules and Regulations
-
- Administrator
- Posts:1301
- Joined:Fri Jun 15, 2018 12:00 pm
- Location:Nigeria
- Donate:
- Has thanked: 6 times
- Been thanked: 104 times
- Status:Offline
- Contact:
Operation : Reset FRP
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM21)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1600400 [8953] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953]...Done
Executing Loader...OK
Auth Enabled Device! You need Mi Auth Account to service!
Skipping Auth...OK
Detecting Chip Type...OK
Hardware : 8953, EMMC, 64 GB
LU Count : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Mi A2 Lite [daisy_sprout]
Brand : xiaomi
Prod.Name : daisy
Software : PKQ1.180917.001.V10.0.20.0.PDLMIXM, V10.0.20.0.PDLMIXM [Fri Mar 27 00:03:10 WIB 2020]
Android Ver. : 9
Patch Level : 2020-03-01
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 6.5
[VIWE IMAGE] XIAOMI MI A2 LITE M1805D1SG TEST POINT
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM21)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1600400 [8953] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953]...Done
Executing Loader...OK
Auth Enabled Device! You need Mi Auth Account to service!
Skipping Auth...OK
Detecting Chip Type...OK
Hardware : 8953, EMMC, 64 GB
LU Count : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Mi A2 Lite [daisy_sprout]
Brand : xiaomi
Prod.Name : daisy
Software : PKQ1.180917.001.V10.0.20.0.PDLMIXM, V10.0.20.0.PDLMIXM [Fri Mar 27 00:03:10 WIB 2020]
Android Ver. : 9
Patch Level : 2020-03-01
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 6.5
[VIWE IMAGE] XIAOMI MI A2 LITE M1805D1SG TEST POINT
Use Search Button to get Instant Results | Follow Forum Rules
Avoid Spams in the forum to prevent banning the offending account. | https://romshillzz.net
Avoid Spams in the forum to prevent banning the offending account. | https://romshillzz.net
-
- Similar Topics
- Replies
- Views
- Last post
-
- 0 Replies
- 5931 Views
-
Last post byRomShillzz
-
- 0 Replies
- 4668 Views
-
Last post byRomShillzz
-
- 0 Replies
- 4436 Views
-
Last post byRomShillzz
-
- 24 Replies
- 12706 Views
-
Last post byRomShillzz
-
- 2 Replies
- 4188 Views
-
Last post byjasmin811