SP Flash Tool Stops Counting and Fails When Flashing Fixed!

Forum rules
READ: GSM-Tutors Forum-Wide Rules and Regulations
READ: GSM-Tutors Forum-Wide Rules and Regulations
-
- Administrator
- Posts: 1290
- Joined: Fri Jun 15, 2018 12:00 pm
- Location: Nigeria
- Donate:
- Has thanked: 6 times
- Been thanked: 101 times
- Status: Offline
- Contact:
SP Flash Tool Stops Counting and Fails When Flashing Fixed!
Are you experiencing some difficulties when flashing a MediaTek (MTK) Android device using SP Flash Tool, Miracle Box or any other MTK Supported tool? When flashing the device, as it is in progress, it stops counting after some percentage and with time pops-up with an unsuccessful result or an error message, If so, here is a fix for you!
Most devices which you are likely to face these issues with when flashing them are those devices with in-built battery. Sometimes during the flashing process, the device would format successfully, but when it starts downloading, reaching to some percentage (maybe 7%, 21%, 50%, etc...) it stops counting!
How To Fix:
#1. The first thing you need to Unscrew the device. After that, Disconnect the battery, Cover the battery terminal with a piece of paper or masking take (so it won't clip when cloosing with the back case).
#2. Now load the Firmware on SP Flash Tool (or any MTK Supported Tool) and flash the device without the battery.
Note: Don't forget to hold the boot key (Vol up + Vol down button) so the device would get connected to your PC.
The flashing process this time around could take a lot of time up-to/lesser or more than an hour (the time taken differs anyway). You can see the attachment below as a prove (the flashing process took 61 min: 19secs which is an hour plus).
#3. After a scuccessful flash, Re-connect the battery, Boot device to recovery menu and Perform a hard reset.
Now your the device should boot & work fine!
If this worked for you, use the thanks button!
Most devices which you are likely to face these issues with when flashing them are those devices with in-built battery. Sometimes during the flashing process, the device would format successfully, but when it starts downloading, reaching to some percentage (maybe 7%, 21%, 50%, etc...) it stops counting!
How To Fix:
#1. The first thing you need to Unscrew the device. After that, Disconnect the battery, Cover the battery terminal with a piece of paper or masking take (so it won't clip when cloosing with the back case).
#2. Now load the Firmware on SP Flash Tool (or any MTK Supported Tool) and flash the device without the battery.
Note: Don't forget to hold the boot key (Vol up + Vol down button) so the device would get connected to your PC.
The flashing process this time around could take a lot of time up-to/lesser or more than an hour (the time taken differs anyway). You can see the attachment below as a prove (the flashing process took 61 min: 19secs which is an hour plus).
#3. After a scuccessful flash, Re-connect the battery, Boot device to recovery menu and Perform a hard reset.
Now your the device should boot & work fine!
If this worked for you, use the thanks button!
Use Search Button to get Instant Results | Follow Forum Rules
Avoid Spams in the forum to prevent banning the offending account. | https://romshillzz.net
Avoid Spams in the forum to prevent banning the offending account. | https://romshillzz.net
-
- Similar Topics
- Replies
- Views
- Last post
-
-
New post Tecno F3 Hang on Boot logo and Support API 3 Fixed
by Techy » Sun Oct 21, 2018 7:06 am » in Other Success Stories - 9 Replies
- 7643 Views
-
Last post by dahaahmed
Wed Sep 09, 2020 2:53 am
-
-
-
New post WALTON PRIMO D5 NEW FLASH FILE UPDATE LCD CAMERA FIXED
by olakunle4luv » Wed Feb 13, 2019 4:06 am » in Walton - 2 Replies
- 2129 Views
-
Last post by Exclusive
Wed Feb 13, 2019 5:28 am
-
-
-
New post Infinix X572 IMEI Fixed Successfully Without Root!!
by RomShillzz » Mon Jul 02, 2018 11:28 pm » in IMEI / Baseband / WiFi / Bluetooth Address Repairs - 2 Replies
- 8352 Views
-
Last post by RomShillzz
Fri Jul 06, 2018 9:44 pm
-
-
-
New post Tecno f3 hang on logo finally fixed
by Bennydiamond » Fri Oct 12, 2018 10:33 am » in Other Success Stories - 1 Replies
- 1514 Views
-
Last post by Exclusive
Fri Oct 12, 2018 1:47 pm
-
-
-
New post Infinix X559/X559C Support API 3 After Removing FRP Fixed [Herfolt Tech]
by Herfolttech » Sun Dec 30, 2018 9:12 am » in Other Success Stories - 4 Replies
- 4049 Views
-
Last post by RomShillzz
Thu Jan 10, 2019 11:10 pm
-